收藏本站

ADE7762
TYPICAL CONNECTION DIAGRAMS
V B ( t ) = 2 × V B × cos ? ? ω l t +
2 π ?
3 ?
?
IAP
CT
V C ( t ) = 2 × V C × cos ? ? ω l t +
4 π ?
3 ?
?
CURRENT CHANNEL CONNECTION
Figure 16 shows a typical connection diagram for the current
channel (IAN). A current transformer (CT) is the current trans-
ducer selected for this example. Notice that the common-mode
voltage for the current channel is AGND and is derived by
center-tapping the burden resistor to AGND. This provides the
complementary analog input signals for IAP and IAN. The CT
turns ratio and Burden Resistor Rb are selected to give a peak
differential voltage of ±500 mV at maximum load.
In theory, it is better to center-tap Rb; however, this requires
very careful attention to the layout and matching of the resistors
to ensure that the channels have the same resistance. A single
resistor may be more practical and is a valid design choice.
Rf
METER CONNECTIONS
In 3-phase service, two main power distribution services exist:
3-phase, 4-wire or 3-phase, 3-wire. The additional wire in the
3-phase, 4-wire arrangement is the neutral wire. The voltage
lines have a phase difference of ±120° (±2π/3 radians) between
each other (see Equation 7).
V A ( t ) = 2 × V A × cos ( ω l t )
? (7)
?
where V A , V B , and V C represent the voltage rms values of the
different phases.
IAN
+ φ B ? ?
I B ( t ) = 2 I B × cos ? ? ω l t +
Cf
Rb ±500mV
IP Rf
Cf
PHASE NEUTRAL
Figure 16. Typical Connection for Current Channels
The current inputs are represented by
I A ( t ) = 2 I A × cos ( ω l t + φ A )
2 π
? 3 ?
(8)
I C ( t ) = 2 I C × cos ? ? ω l t +
+ φ C ? ?
VOLTAGE CHANNEL CONNECTION
Figure 17 shows two typical connections for the voltage chan-
?
4 π
3
?
nel. The first option uses a potential transformer (PT) to pro-
vide complete isolation from the main voltage. In the second
option, the ADE7762 is biased around the neutral wire, and a
resistor divider is used to provide a voltage signal proportional
to the line voltage. Adjusting the ratio of Ra, Rb, and VR is a
convenient way of carrying out a gain calibration on the meter.
VR can be implemented using either a potentiometer or a
binary weighted series of resistors. Either configuration works,
however, the potentiometer is subject to noise over time. Two
fixed value resistors can be used in place of VR to minimize
where:
I A , I B , and I C represent the rms value of the current of each
phase.
φ A , φ B , and φ C represent the phase difference of the current and
voltage channel of each phase.
The instantaneous powers can then be calculated as follows:
P A (t) = V A (t) × I A (t)
P B (t) = V B (t) × I B (t)
P C (t) = V C (t) × I C (t)
the noise.
PT
±500mV
Rf
Cf
VAP
VN
Then,
P A ( t ) = V A × I A × cos ( φ A ) ? V A × I A × cos ( 2 ω l t + φ A )
P B ( t ) =
V B × I B × cos ( φ B ) ? V B × I B × cos ? ? 2 ω l t +
+ φ B ? ? (9)
AGND
Rf
Cf
?
4 π
3
?
P C ( t ) = V C × I C × cos ( φ C ) ? V C × I C × cos ? ? 2 ω l t +
+ φ C ? ?
PHASE   NEUTRAL
Ra *
Cf
?
8 π
3
?
Rb*
VR*
±500mV
Rf
VAP
VN
As shown in Equation 9, the active power calculation per phase
is made when current and voltage inputs of one phase are
Cf
PHASE NEUTRAL
*Ra >> Rf + VR; *Rb + VR = Rf
Figure 17. Typical Connections for Voltage Channels
connected to the same channel (A, B, or C). Then the
summation of each individual active power calculation gives the
total active power information, P ( t ) = P A ( t ) + P B ( t ) + P C ( t ).
Rev. 0 | Page 15 of 28
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
EVAL-ADE7763ZEB BOARD EVALUATION FOR ADE7763
EVAL-ADE7816EBZ BOARD EVALUATION FOR ADE7816
EVAL-ADE7878EBZ BOARD EVAL FOR ADE7878
EVAL-ADE7880EBZ BOARD EVAL FOR ADE7880
EVAL-ADE7953EBZ BOARD EVAL FOR ADE7953
EVAL-ADF4002EBZ1 BOARD EVAL FOR ADF4002
EVAL-ADG788EBZ BOARD EVALUATION FOR ADG788
EVAL-ADM1021AEB BOARD EVAL FOR ADM1021
相关代理商/技术参数
EVAL-ADE7763EB 制造商:Analog Devices 功能描述:EVALUATION BOARD DOCUMENTATION ADE7763 ENERGY METERING IC
EVAL-ADE7763ZEB 功能描述:BOARD EVALUATION FOR ADE7763 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源
EVAL-ADE7816EBZ 功能描述:BOARD EVALUATION FOR ADE7816 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源
EVAL-ADE7854EBZ 制造商:Analog Devices 功能描述:EVALUATION BOARDS - Boxed Product (Development Kits)
EVAL-ADE7858EBZ 制造商:AD 制造商全称:Analog Devices 功能描述:Poly Phase Multifunction Energy Metering IC with per Phase Active and Reactive Powers
EVAL-ADE7878EBZ 功能描述:BOARD EVAL FOR ADE7878 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板
EVAL-ADE7880EBZ 功能描述:BOARD EVAL FOR ADE7880 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理，电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板
EVAL-ADE7880EBZ 制造商:Analog Devices 功能描述:ADE7880, ENERGY METER, 3 PH, SPI, I2C, E